IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i13p3779-d580840.html
   My bibliography  Save this article

Study of the Influence of the Lack of Contact in Plate and Fin and Tube Heat Exchanger on Heat Transfer Efficiency under Periodic Flow Conditions

Author

Listed:
  • Marcin Łęcki

    (Faculty of Mechanical Engineering, Institute of Turbomachinery, Lodz University of Technology, 219/223 Wolczanska Street, 90-924 Lodz, Poland)

  • Dariusz Andrzejewski

    (Faculty of Mechanical Engineering, Institute of Turbomachinery, Lodz University of Technology, 219/223 Wolczanska Street, 90-924 Lodz, Poland)

  • Artur N. Gutkowski

    (Faculty of Mechanical Engineering, Institute of Turbomachinery, Lodz University of Technology, 219/223 Wolczanska Street, 90-924 Lodz, Poland)

  • Grzegorz Górecki

    (Faculty of Mechanical Engineering, Institute of Turbomachinery, Lodz University of Technology, 219/223 Wolczanska Street, 90-924 Lodz, Poland)

Abstract

Plate fin-tube heat exchangers are widely used in air conditioning and refrigeration systems and other industry fields. Various errors made in the manufacturing process can result in the formation of an air gap between the tube and fin. Several numerical simulations were carried out for a symmetric section of plate fin-tube heat exchanger to study the influence of air gap on heat transfer under periodic flow conditions. Different locations and sizes of an air gap spanning 1/2 circumference of the tube were considered for the range of airflow velocities. Velocity and temperature fields for cases with air gap were compared with ideal thermal contact cases. Blocking of heat flow by the gap leads to the reduction of heat transfer rate. Fin discontinuity in the front of the tube causes the smallest reduction of the heat transfer rate in comparison to the ideal tube-fin contact, especially for thin slits. The rear gap position is the worst in the smallest gap range. Therefore, reversing the flow direction can lead to up to a 15% heat transfer increase, if mainly the rear gaps are present. The introduction of a thin slit in the front of the tube leads to convective heat transfer enhancement, which should be further investigated.

Suggested Citation

  • Marcin Łęcki & Dariusz Andrzejewski & Artur N. Gutkowski & Grzegorz Górecki, 2021. "Study of the Influence of the Lack of Contact in Plate and Fin and Tube Heat Exchanger on Heat Transfer Efficiency under Periodic Flow Conditions," Energies, MDPI, vol. 14(13), pages 1-25, June.
    • Handle: RePEc:gam:jeners:v:14:y:2021:i:13:p:3779-:d:580840
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/13/3779/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/14/13/3779/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Lei Chai & Savvas A. Tassou, 2018. "A Review of Airside Heat Transfer Augmentation with Vortex Generators on Heat Transfer Surface," Energies, MDPI, vol. 11(10), pages 1-45, October.
    2. Lotfi, Babak & Sundén, Bengt & Wang, Qiuwang, 2016. "An investigation of the thermo-hydraulic performance of the smooth wavy fin-and-elliptical tube heat exchangers utilizing new type vortex generators," Applied Energy, Elsevier, vol. 162(C), pages 1282-1302.
    3. Dawid Taler & Jan Taler & Marcin Trojan, 2020. "Experimental Verification of an Analytical Mathematical Model of a Round or Oval Tube Two-Row Car Radiator," Energies, MDPI, vol. 13(13), pages 1-23, July.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Krzysztof Rajski & Jan Danielewicz, 2023. "Heat Transfer and Heat Recovery Systems," Energies, MDPI, vol. 16(7), pages 1-6, April.
    2. Mateusz Marcinkowski & Dawid Taler & Jan Taler & Katarzyna Węglarz, 2021. "Thermal Calculations of Four-Row Plate-Fin and Tube Heat Exchanger Taking into Account Different Air-Side Correlations on Individual Rows of Tubes for Low Reynold Numbers," Energies, MDPI, vol. 14(21), pages 1-13, October.
    3. Mirosław Neska & Mirosław Mrozek & Marta Żurek-Mortka & Andrzej Majcher, 2021. "Analysis of the Parameters of the Two-Sections Hot Side Heat Exchanger of the Module with Thermoelectric Generators," Energies, MDPI, vol. 14(16), pages 1-15, August.
    4. Wan-Ling Hu & Ai-Jun Ma & Yong Guan & Zhi-Jie Cui & Yi-Bo Zhang & Jing Wang, 2021. "Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions," Energies, MDPI, vol. 14(21), pages 1-15, October.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Junjie Zhao & Bin Zhang & Xiaoli Fu & Shenglin Yan, 2021. "Numerical Study on the Influence of Vortex Generator Arrangement on Heat Transfer Enhancement of Oil-Cooled Motor," Energies, MDPI, vol. 14(21), pages 1-17, October.
    2. Mateusz Marcinkowski & Dawid Taler & Jan Taler & Katarzyna Węglarz, 2021. "Thermal Calculations of Four-Row Plate-Fin and Tube Heat Exchanger Taking into Account Different Air-Side Correlations on Individual Rows of Tubes for Low Reynold Numbers," Energies, MDPI, vol. 14(21), pages 1-13, October.
    3. Shahsavar, Amin & Al-Rashed, Abdullah A.A.A. & Entezari, Sajad & Sardari, Pouyan Talebizadeh, 2019. "Melting and solidification characteristics of a double-pipe latent heat storage system with sinusoidal wavy channels embedded in a porous medium," Energy, Elsevier, vol. 171(C), pages 751-769.
    4. Tang, Song-Zhen & Wang, Fei-Long & He, Ya-Ling & Yu, Yang & Tong, Zi-Xiang, 2019. "Parametric optimization of H-type finned tube with longitudinal vortex generators by response surface model and genetic algorithm," Applied Energy, Elsevier, vol. 239(C), pages 908-918.
    5. Zhao, Xiaohuan & E, Jiaqiang & Zhang, Zhiqing & Chen, Jingwei & Liao, Gaoliang & Zhang, Feng & Leng, Erwei & Han, Dandan & Hu, Wenyu, 2020. "A review on heat enhancement in thermal energy conversion and management using Field Synergy Principle," Applied Energy, Elsevier, vol. 257(C).
    6. Lei Chai & Savvas A. Tassou, 2018. "A Review of Airside Heat Transfer Augmentation with Vortex Generators on Heat Transfer Surface," Energies, MDPI, vol. 11(10), pages 1-45, October.
    7. Yerzhan Asem Anuarkyzy & Marat B. Koshumbaev, 2016. "New Design of Low-Head Hydro Turbine for Small-Scale Hydropower Plant," International Journal of Technology and Engineering Studies, PROF.IR.DR.Mohid Jailani Mohd Nor, vol. 2(3), pages 87-94.
    8. Rishikesh Sharma & Dipti Prasad Mishra & Marek Wasilewski & Lakhbir Singh Brar, 2023. "Application of Response Surface Methodology and Artificial Neural Network to Optimize the Curved Trapezoidal Winglet Geometry for Enhancing the Performance of a Fin-and-Tube Heat Exchanger," Energies, MDPI, vol. 16(10), pages 1-30, May.
    9. Choi, Seok Min & Kwon, Hyun Goo & Kim, Taehyun & Moon, Hee Koo & Cho, Hyung Hee, 2022. "Active cooling of photovoltaic (PV) cell by acoustic excitation in single-dimpled internal channel," Applied Energy, Elsevier, vol. 309(C).
    10. Shahsavar, Amin & Majidzadeh, Amir Hossein & Mahani, Roohollah Babaei & Talebizadehsardari, Pouyan, 2021. "Entropy and thermal performance analysis of PCM melting and solidification mechanisms in a wavy channel triplex-tube heat exchanger," Renewable Energy, Elsevier, vol. 165(P2), pages 52-72.
    11. Dezan, Daniel J. & Rocha, André D. & Ferreira, Wallace G., 2020. "Parametric sensitivity analysis and optimisation of a solar air heater with multiple rows of longitudinal vortex generators," Applied Energy, Elsevier, vol. 263(C).
    12. Ali Sadeghianjahromi & Saeid Kheradmand & Hossain Nemati & Jane-Sunn Liaw & Chi-Chuan Wang, 2018. "Compound Heat Transfer Enhancement of Wavy Fin-and-Tube Heat Exchangers through Boundary Layer Restarting and Swirled Flow," Energies, MDPI, vol. 11(8), pages 1-19, July.
    13. Ruben Gutierrez-Amo & Unai Fernandez-Gamiz & Iñigo Errasti & Ekaitz Zulueta, 2018. "Computational Modelling of Three Different Sub-Boundary Layer Vortex Generators on a Flat Plate," Energies, MDPI, vol. 11(11), pages 1-21, November.
    14. Zuoqin Qian & Qiang Wang & Song Lv, 2020. "Research on the Thermal Hydraulic Performance and Entropy Generation Characteristics of Finned Tube Heat Exchanger with Streamline Tube," Energies, MDPI, vol. 13(20), pages 1-28, October.
    15. Feng, Zhenfei & Jiang, Ping & Zheng, Siyao & Zhang, Qingyuan & Chen, Zhen & Guo, Fangwen & Zhang, Jinxin, 2023. "Experimental and numerical investigations on the effects of insertion-type longitudinal vortex generators on flow and heat transfer characteristics in square minichannels," Energy, Elsevier, vol. 278(PA).
    16. Gaoliang Liao & Zhizhou Li & Feng Zhang & Lijun Liu & Jiaqiang E, 2021. "A Review on the Thermal-Hydraulic Performance and Optimization of Compact Heat Exchangers," Energies, MDPI, vol. 14(19), pages 1-35, September.
    17. R. S. Varun Kumar & M. D. Alsulami & I. E. Sarris & G. Sowmya & Fehmi Gamaoun, 2023. "Stochastic Levenberg–Marquardt Neural Network Implementation for Analyzing the Convective Heat Transfer in a Wavy Fin," Mathematics, MDPI, vol. 11(10), pages 1-26, May.
    18. Azeez mohammed Hussein, Hind & Zulkifli, Rozli & Faizal Bin Wan Mahmood, Wan Mohd & Ajeel, Raheem K., 2022. "Structure parameters and designs and their impact on performance of different heat exchangers: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    19. Alam, Tabish & Kim, Man-Hoe, 2018. "A comprehensive review on single phase heat transfer enhancement techniques in heat exchanger applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 81(P1), pages 813-839.
    20. Norouzi, Amir Mohammad & Siavashi, Majid & Ahmadi, Rouhollah & Tahmasbi, Milad, 2021. "Experimental study of a parabolic trough solar collector with rotating absorber tube," Renewable Energy, Elsevier, vol. 168(C), pages 734-749.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:13:p:3779-:d:580840. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.