IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v12y2019i21p4085-d280465.html
   My bibliography  Save this article

Numerical and Experimental Study on a High-Power Cold Achieving Process of a Coil-Plate Ice-Storage System

Author

Listed:
  • Liang Guo

    (Department of Thermal Science and Energy Engineering, University of Science and Technology of China, Hefei 230027, China)

  • Hong Ye

    (Department of Thermal Science and Energy Engineering, University of Science and Technology of China, Hefei 230027, China)

Abstract

Heat dissipation of high-power lasers needs a cold storage and supply system to provide sufficient cooling power. A compact coil-plate heat exchange device has been proposed and applied in the phase-change cold storage system with ice as the cold-storage medium and glycol aqueous solution as the coolant. The heat exchanger consists of several stacked coil-plate units and each unit is constructed with a flat plate and serpentine coils welded on the plate. A simulation model on the cold achieving process of a coil-plate unit was built and verified by the corresponding experiment. The influences of the structural parameters (tube diameter, tube pitch, and plate spacing) of the unit and the inlet temperature and volume flow rate of the coolant on the heat exchange power density were analyzed to obtain the maximal cooling effect in a limited time period. It was found that the heat exchange power density is limited when the tube pitch and plate spacing are large, otherwise, the effective cooling time period is limited. A small plate spacing can make the power density decrease rapidly in the later stage. The inlet coolant temperature can significantly affect the heat exchange power density while the coolant volume flow rate in tube has a small effect on the power density when the coolant is in turbulent state. In a time period of 900 s, for a coil-plate heat exchanger with a plate size of 940 mm ×770 mm and a tube pitch of 78 mm, when the plate spacing is 20 mm, the average heat exchange power density is 5.1 kW/m 2 when the inlet temperature and volume flow rate of the coolant are 20 °C and 0.5 m 3 /h, respectively. The total cooling power of several stacked coil-plate units in the limited time period can match the high requirement of laser heat dissipation.

Suggested Citation

  • Liang Guo & Hong Ye, 2019. "Numerical and Experimental Study on a High-Power Cold Achieving Process of a Coil-Plate Ice-Storage System," Energies, MDPI, vol. 12(21), pages 1-11, October.
    • Handle: RePEc:gam:jeners:v:12:y:2019:i:21:p:4085-:d:280465
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/12/21/4085/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/12/21/4085/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Oró, E. & de Gracia, A. & Castell, A. & Farid, M.M. & Cabeza, L.F., 2012. "Review on phase change materials (PCMs) for cold thermal energy storage applications," Applied Energy, Elsevier, vol. 99(C), pages 513-533.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Peter Sivák & Peter Tauš & Radim Rybár & Martin Beer & Zuzana Šimková & František Baník & Sergey Zhironkin & Jana Čitbajová, 2020. "Analysis of the Combined Ice Storage (PCM) Heating System Installation with Special Kind of Solar Absorber in an Older House," Energies, MDPI, vol. 13(15), pages 1-20, July.
    2. Robert Sekret & Przemysław Starzec, 2021. "Developing a Cold Accumulator with a Capsule Bed Containing Water as a Phase-Change Material," Energies, MDPI, vol. 14(9), pages 1-18, May.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Kousksou, T. & El Rhafiki, T. & Jamil, A. & Bruel, P. & Zeraouli, Y., 2013. "PCMs inside emulsions: Some specific aspects related to DSC (differential scanning calorimeter)-like configurations," Energy, Elsevier, vol. 56(C), pages 175-183.
    2. Lukas Hegner & Stefan Krimmel & Rebecca Ravotti & Dominic Festini & Jörg Worlitschek & Anastasia Stamatiou, 2021. "Experimental Feasibility Study of a Direct Contact Latent Heat Storage Using an Ester as a Bio-Based Storage Material," Energies, MDPI, vol. 14(2), pages 1-26, January.
    3. Nassima Radouane, 2022. "A Comprehensive Review of Composite Phase Change Materials (cPCMs) for Thermal Management Applications, Including Manufacturing Processes, Performance, and Applications," Energies, MDPI, vol. 15(21), pages 1-28, November.
    4. Fan, Li-Wu & Fang, Xin & Wang, Xiao & Zeng, Yi & Xiao, Yu-Qi & Yu, Zi-Tao & Xu, Xu & Hu, Ya-Cai & Cen, Ke-Fa, 2013. "Effects of various carbon nanofillers on the thermal conductivity and energy storage properties of paraffin-based nanocomposite phase change materials," Applied Energy, Elsevier, vol. 110(C), pages 163-172.
    5. Wang, X.J. & Li, X.F. & Xu, Y.H. & Zhu, D.S., 2014. "Thermal energy storage characteristics of Cu–H2O nanofluids," Energy, Elsevier, vol. 78(C), pages 212-217.
    6. Li, Yanchen & Wang, Beibei & Zhang, Weiye & Zhao, Junqi & Fang, Xiaoyang & Sun, Jingmeng & Xia, Rongqi & Guo, Hongwu & Liu, Yi, 2022. "Processing wood into a phase change material with high solar-thermal conversion efficiency by introducing stable polyethylene glycol-based energy storage polymer," Energy, Elsevier, vol. 254(PA).
    7. Al-Shannaq, Refat & Young, Brent & Farid, Mohammed, 2019. "Cold energy storage in a packed bed of novel graphite/PCM composite spheres," Energy, Elsevier, vol. 171(C), pages 296-305.
    8. Valerie Eveloy & Dereje S. Ayou, 2019. "Sustainable District Cooling Systems: Status, Challenges, and Future Opportunities, with Emphasis on Cooling-Dominated Regions," Energies, MDPI, vol. 12(2), pages 1-64, January.
    9. Zhu, Kai & Li, Xueqiang & Campana, Pietro Elia & Li, Hailong & Yan, Jinyue, 2018. "Techno-economic feasibility of integrating energy storage systems in refrigerated warehouses," Applied Energy, Elsevier, vol. 216(C), pages 348-357.
    10. Shafie-khah, M. & Kheradmand, M. & Javadi, S. & Azenha, M. & de Aguiar, J.L.B. & Castro-Gomes, J. & Siano, P. & Catalão, J.P.S., 2016. "Optimal behavior of responsive residential demand considering hybrid phase change materials," Applied Energy, Elsevier, vol. 163(C), pages 81-92.
    11. Pitié, F. & Zhao, C.Y. & Baeyens, J. & Degrève, J. & Zhang, H.L., 2013. "Circulating fluidized bed heat recovery/storage and its potential to use coated phase-change-material (PCM) particles," Applied Energy, Elsevier, vol. 109(C), pages 505-513.
    12. Sun, Xiaoqin & Zhang, Quan & Medina, Mario A. & Liao, Shuguang, 2015. "Performance of a free-air cooling system for telecommunications base stations using phase change materials (PCMs): In-situ tests," Applied Energy, Elsevier, vol. 147(C), pages 325-334.
    13. Rostami, Sara & Afrand, Masoud & Shahsavar, Amin & Sheikholeslami, M. & Kalbasi, Rasool & Aghakhani, Saeed & Shadloo, Mostafa Safdari & Oztop, Hakan F., 2020. "A review of melting and freezing processes of PCM/nano-PCM and their application in energy storage," Energy, Elsevier, vol. 211(C).
    14. Shi, X.J. & Zhang, P., 2013. "A comparative study of different methods for the generation of tetra-n-butyl ammonium bromide clathrate hydrate slurry in a cold storage air-conditioning system," Applied Energy, Elsevier, vol. 112(C), pages 1393-1402.
    15. Wang, Ting & Qiu, Xiaolin & Chen, Xiaojing & Lu, Lixin & Zhou, Binglin, 2022. "Sponge-like form-stable phase change materials with embedded graphene oxide for enhancing the thermal storage efficiency and the temperature response in transport packaging applications," Applied Energy, Elsevier, vol. 325(C).
    16. Fan, Li-Wu & Yao, Xiao-Li & Wang, Xiao & Wu, Yu-Yue & Liu, Xue-Ling & Xu, Xu & Yu, Zi-Tao, 2015. "Non-isothermal crystallization of aqueous nanofluids with high aspect-ratio carbon nano-additives for cold thermal energy storage," Applied Energy, Elsevier, vol. 138(C), pages 193-201.
    17. Li, Xinyi & Ma, Ting & Liu, Jun & Zhang, Hao & Wang, Qiuwang, 2018. "Pore-scale investigation of gravity effects on phase change heat transfer characteristics using lattice Boltzmann method," Applied Energy, Elsevier, vol. 222(C), pages 92-103.
    18. Li, Yantong & Nord, Natasa & Yin, Huibin, 2023. "An investigation of using CO2 heat pumps to charge PCM storage tank for domestic use," Renewable Energy, Elsevier, vol. 218(C).
    19. Park, Joon Ho & Park, Jungjoon & Lee, Jae Won & Kang, Yong Tae, 2023. "Progress in CO2 hydrate formation and feasibility analysis for cold thermal energy harvesting application," Renewable and Sustainable Energy Reviews, Elsevier, vol. 187(C).
    20. Enescu, Diana & Virjoghe, Elena Otilia, 2014. "A review on thermoelectric cooling parameters and performance," Renewable and Sustainable Energy Reviews, Elsevier, vol. 38(C), pages 903-916.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:12:y:2019:i:21:p:4085-:d:280465. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.