IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v201y2020ics0360544220307684.html
   My bibliography  Save this article

The influence of plate corrugations geometry scale factor on performance of plate heat exchanger as condenser of vapour from its mixture with noncondensing gas

Author

Listed:
  • Kapustenko, Petro O.
  • Klemeš, Jiří Jaromír
  • Arsenyeva, Olga P.
  • Kusakov, Sergey K.
  • Tovazhnyanskyy, Leonid L.

Abstract

The condensation of steam from a steam-air mixture is studied experimentally at three samples of Plate Heat Exchanger (PHE) channel. For three test samples corrugations are similar but differ in scale with the height 5, 7.5 and 10 mm. The results of tests are compared to calculations with one dimensional mathematical model of the process. The identification of correlations for local heat and mass transfer coefficients, as also friction factor in condensing two-phase flow, is made by comparison of computed results with tests data. The correlations for condensing two-phase flow are based on single-phase correlations for considered channels. For mass transfer coefficients, the best results are obtained using a stagnant film model for accounting transverse mass flux influence. For the prediction of pressure losses in two-phase condensing flow, the correlation with Lockhart-Martinelli parameters is used for zones of low liquid flow rates. For other channelzones are proposed its combination with an equation based on a dispersed annular model of flow structure. The presented equations can be used for calculation of heat and mass transfer intensity and pressure losses in two-phase condensing flow when designing PHE for condensation of steam from its mixture with air by local process parameters.

Suggested Citation

  • Kapustenko, Petro O. & Klemeš, Jiří Jaromír & Arsenyeva, Olga P. & Kusakov, Sergey K. & Tovazhnyanskyy, Leonid L., 2020. "The influence of plate corrugations geometry scale factor on performance of plate heat exchanger as condenser of vapour from its mixture with noncondensing gas," Energy, Elsevier, vol. 201(C).
    • Handle: RePEc:eee:energy:v:201:y:2020:i:c:s0360544220307684
    DOI: 10.1016/j.energy.2020.117661
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544220307684
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2020.117661?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Perevertaylenko, Olexander Yu. & Gariev, Andriy O. & Damartzis, Theodoros & Tovazhnyanskyy, Leonid L. & Kapustenko, Petro O. & Arsenyeva, Olga P., 2015. "Searches of cost effective ways for amine absorption unit design in CO2 post-combustion capture process," Energy, Elsevier, vol. 90(P1), pages 105-112.
    2. Walmsley, Timothy G. & Walmsley, Michael R.W. & Atkins, Martin J. & Neale, James R. & Tarighaleslami, Amir H., 2015. "Thermo-economic optimisation of industrial milk spray dryer exhaust to inlet air heat recovery," Energy, Elsevier, vol. 90(P1), pages 95-104.
    3. Srinivasan, Kalyan K. & Mago, Pedro J. & Krishnan, Sundar R., 2010. "Analysis of exhaust waste heat recovery from a dual fuel low temperature combustion engine using an Organic Rankine Cycle," Energy, Elsevier, vol. 35(6), pages 2387-2399.
    4. Satyavada, Harish & Baldi, Simone, 2018. "Monitoring energy efficiency of condensing boilers via hybrid first-principle modelling and estimation," Energy, Elsevier, vol. 142(C), pages 121-129.
    5. Wan, Wei & Engvall, Klas & Yang, Weihong & Möller, Björn Fredriksson, 2018. "Experimental and modelling studies on condensation of inorganic species during cooling of product gas from pressurized biomass fluidized bed gasification," Energy, Elsevier, vol. 153(C), pages 35-44.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Kapustenko, Petro & Klemeš, Jiří Jaromír & Arsenyeva, Olga & Tovazhnyanskyy, Leonid & Zorenko, Viktor, 2021. "Pressure drop in two phase flow of condensing air-steam mixture inside PHE channels formed by plates with corrugations of different geometries," Energy, Elsevier, vol. 228(C).
    2. Petro Kapustenko & Jiří Jaromír Klemeš & Olga Arsenyeva & Leonid Tovazhnyanskyy, 2023. "PHE (Plate Heat Exchanger) for Condensing Duties: Recent Advances and Future Prospects," Energies, MDPI, vol. 16(1), pages 1-18, January.
    3. Arsenyeva, Olga & Klemeš, Jiří Jaromír & Klochock, Eugeny & Kapustenko, Petro, 2023. "The effect of plate size and corrugation pattern on plate heat exchanger performance in specific conditions of steam-air mixture condensation," Energy, Elsevier, vol. 263(PC).
    4. Seferlis, Panos & Varbanov, Petar Sabev & Papadopoulos, Athanasios I. & Chin, Hon Huin & Klemeš, Jiří Jaromír, 2021. "Sustainable design, integration, and operation for energy high-performance process systems," Energy, Elsevier, vol. 224(C).
    5. Wang, Bohong & Klemeš, Jiří Jaromír & Li, Nianqi & Zeng, Min & Varbanov, Petar Sabev & Liang, Yongtu, 2021. "Heat exchanger network retrofit with heat exchanger and material type selection: A review and a novel method," Renewable and Sustainable Energy Reviews, Elsevier, vol. 138(C).
    6. Arsenyeva, Olga & Klemeš, Jiří Jaromír & Kapustenko, Petro & Fedorenko, Olena & Kusakov, Sergiy & Kobylnik, Dmytro, 2021. "Plate heat exchanger design for the utilisation of waste heat from exhaust gases of drying process," Energy, Elsevier, vol. 233(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Arsenyeva, Olga & Klemeš, Jiří Jaromír & Tovazhnyanskyy, Leonid & Klochok, Eugeny & Kapustenko, Petro, 2023. "Estimating parameters of plate heat exchanger for condensation of steam from mixture with air as a component of heat exchanger network," Energy, Elsevier, vol. 283(C).
    2. Arsenyeva, Olga & Klemeš, Jiří Jaromír & Klochock, Eugeny & Kapustenko, Petro, 2023. "The effect of plate size and corrugation pattern on plate heat exchanger performance in specific conditions of steam-air mixture condensation," Energy, Elsevier, vol. 263(PC).
    3. Mamat, Aman M.I. & Romagnoli, Alessandro & Martinez-Botas, Ricardo F., 2014. "Characterisation of a low pressure turbine for turbocompounding applications in a heavily downsized mild-hybrid gasoline engine," Energy, Elsevier, vol. 64(C), pages 3-16.
    4. Vélez, Fredy & Segovia, José J. & Martín, M. Carmen & Antolín, Gregorio & Chejne, Farid & Quijano, Ana, 2012. "A technical, economical and market review of organic Rankine cycles for the conversion of low-grade heat for power generation," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(6), pages 4175-4189.
    5. Chintala, V. & Subramanian, K.A., 2015. "Experimental investigations on effect of different compression ratios on enhancement of maximum hydrogen energy share in a compression ignition engine under dual-fuel mode," Energy, Elsevier, vol. 87(C), pages 448-462.
    6. Kim, Dong Kyu & Lee, Ji Sung & Kim, Jinwoo & Kim, Mo Se & Kim, Min Soo, 2017. "Parametric study and performance evaluation of an organic Rankine cycle (ORC) system using low-grade heat at temperatures below 80°C," Applied Energy, Elsevier, vol. 189(C), pages 55-65.
    7. Olga Arsenyeva & Leonid Tovazhnyanskyy & Petro Kapustenko & Jiří Jaromír Klemeš & Petar Sabev Varbanov, 2023. "Review of Developments in Plate Heat Exchanger Heat Transfer Enhancement for Single-Phase Applications in Process Industries," Energies, MDPI, vol. 16(13), pages 1-28, June.
    8. Arsenyeva, Olga & Klemeš, Jiří Jaromír & Kapustenko, Petro & Fedorenko, Olena & Kusakov, Sergiy & Kobylnik, Dmytro, 2021. "Plate heat exchanger design for the utilisation of waste heat from exhaust gases of drying process," Energy, Elsevier, vol. 233(C).
    9. Wang, E.H. & Zhang, H.G. & Zhao, Y. & Fan, B.Y. & Wu, Y.T. & Mu, Q.H., 2012. "Performance analysis of a novel system combining a dual loop organic Rankine cycle (ORC) with a gasoline engine," Energy, Elsevier, vol. 43(1), pages 385-395.
    10. Yang, Fubin & Cho, Heejin & Zhang, Hongguang & Zhang, Jian, 2017. "Thermoeconomic multi-objective optimization of a dual loop organic Rankine cycle (ORC) for CNG engine waste heat recovery," Applied Energy, Elsevier, vol. 205(C), pages 1100-1118.
    11. Li, Jing & Alvi, Jahan Zeb & Pei, Gang & Su, Yuehong & Li, Pengcheng & Gao, Guangtao & Ji, Jie, 2016. "Modelling of organic Rankine cycle efficiency with respect to the equivalent hot side temperature," Energy, Elsevier, vol. 115(P1), pages 668-683.
    12. Shu, Gequn & Liu, Lina & Tian, Hua & Wei, Haiqiao & Yu, Guopeng, 2014. "Parametric and working fluid analysis of a dual-loop organic Rankine cycle (DORC) used in engine waste heat recovery," Applied Energy, Elsevier, vol. 113(C), pages 1188-1198.
    13. Liu, Chao & He, Chao & Gao, Hong & Xie, Hui & Li, Yourong & Wu, Shuangying & Xu, Jinliang, 2013. "The environmental impact of organic Rankine cycle for waste heat recovery through life-cycle assessment," Energy, Elsevier, vol. 56(C), pages 144-154.
    14. Bahlouli, Keyvan & Khoshbakhti Saray, Rahim, 2016. "Energetic and exergetic analyses of a new energy system for heating and power production purposes," Energy, Elsevier, vol. 106(C), pages 390-399.
    15. Sarabchi, N. & Khoshbakhti Saray, R. & Mahmoudi, S.M.S., 2013. "Utilization of waste heat from a HCCI (homogeneous charge compression ignition) engine in a tri-generation system," Energy, Elsevier, vol. 55(C), pages 965-976.
    16. Caglayan, Hasan & Caliskan, Hakan, 2017. "Sustainability assessment of heat exchanger units for spray dryers," Energy, Elsevier, vol. 124(C), pages 741-751.
    17. Song, Jian & Song, Yin & Gu, Chun-wei, 2015. "Thermodynamic analysis and performance optimization of an Organic Rankine Cycle (ORC) waste heat recovery system for marine diesel engines," Energy, Elsevier, vol. 82(C), pages 976-985.
    18. Dosa, Ion, 2014. "Power Plant Waste Heat Recovery for Household Heating Using Heat Pumps," MPRA Paper 62961, University Library of Munich, Germany.
    19. Kapustenko, Petro & Klemeš, Jiří Jaromír & Arsenyeva, Olga & Tovazhnyanskyy, Leonid & Zorenko, Viktor, 2021. "Pressure drop in two phase flow of condensing air-steam mixture inside PHE channels formed by plates with corrugations of different geometries," Energy, Elsevier, vol. 228(C).
    20. Saidur, R. & Rezaei, M. & Muzammil, W.K. & Hassan, M.H. & Paria, S. & Hasanuzzaman, M., 2012. "Technologies to recover exhaust heat from internal combustion engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(8), pages 5649-5659.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:201:y:2020:i:c:s0360544220307684. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.