IDEAS home Printed from https://ideas.repec.org/h/baq/pcchap/978-617-7319-97-8-ch1.html
   My bibliography  Save this book chapter

Cast and deformation strengthened alloys of the Al-Mg-Sc system

In: STRUCTURAL MATERIALS: MANUFACTURE, PROPERTIES, CONDITIONS OF USE

Author

Listed:
  • Orest Ostash

    (Karpenko Physico-Mechanical Institute of National Academy of Sciences of Ukraine)

  • Svitlana Polyvoda

    (Physico-Technological Institute of Metals and Alloys of National Academy of Sciences of Ukraine)

  • Andrii Titov

    (National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”)

  • Kostyantyn Balushok

    (Motor Sich JSC)

  • Roman Chepil

    (Karpenko Physico-Mechanical Institute of National Academy of Sciences of Ukraine)

  • Natalia Zlochevska

    (National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”)

Abstract

The effect of reducing the magnesium content and doping with scandium, zirconium, manganese, chromium, and rare-earth metals on the structure, phase composition, strength, plasticity, and crack resistance, as well as the potential and corrosion current of alloys of the Al-Mg and Al-Mg-Sc systems obtained using magnetohydrodynamic foundry was investigated. Installation a positive effect of reducing the magnesium content, replacing manganese with chromium, and alloying with lanthanum in alloys of the Al-Mg-Sc system in the cast state and after deformation processing (extrusion, pressing, and rolling) was established. It is shown that due to dispersion strengthening by secondary intermetallics of chromium and lanthanum, this alloy in the cast state after homogenization is superior in strength to the well-known alloys of grades 1570 and 1545. After hot and cold rolling, it is not inferior to these alloys in terms of strength and plasticity, but has higher corrosion resistance characteristics. It was found that in terms of structural strength, which is comprehensively determined by the characteristics of strength and cyclic crack resistance, such alloys are superior to the well-known Al-Mg-Sc, Al-Mg and Al-Cu-Mg systems. The results of modeling the stress-strain state and damage of strips of different thicknesses during hot isothermal pressing are presented. The temperature-force parameters of the process and the geometry of the pressed strip are set to obtain its minimal damage.

Suggested Citation

  • Orest Ostash & Svitlana Polyvoda & Andrii Titov & Kostyantyn Balushok & Roman Chepil & Natalia Zlochevska, 2023. "Cast and deformation strengthened alloys of the Al-Mg-Sc system," Chapters of Monographs, in: STRUCTURAL MATERIALS: MANUFACTURE, PROPERTIES, CONDITIONS OF USE, chapter 1, pages 2-31, PC TECHNOLOGY CENTER.
    • Handle: RePEc:baq:pcchap:978-617-7319-97-8-ch1
    DOI: 10.15587/978-617-7319-97-8.ch1
    as

    Download full text from publisher

    File URL: http://monograph.com.ua/pctc/catalog/view/978-617-7319-97-8.ch1/223/874-1
    Download Restriction: no
    File URL: https://libkey.io/10.15587/978-617-7319-97-8.ch1?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:baq:pcchap:978-617-7319-97-8-ch1. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Iryna Prudius (email available below). General contact details of provider: http://monograph.com.ua/pctc/catalog .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.