Author
Listed:
- M. RUSOP
(Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan)
- K. UMA
(Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan)
- T. SOGA
(Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan)
- T. JIMBO
(Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan;
Research Center for Nano-Device and System, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan)
Abstract
The transparentc-axis orientedZnOthin films have been prepared by sol–gel method using zinc acetate as cations source, 2-mrthoxiethanol as solvent and monoethanolamine as sol stabilizer. Film deposition was performed by dip coating technique at a withdrawal rate of 10 mm/min on quartz and silicon substrates. The effect of annealing temperature in air ambient from 100 to 800°C on the structural, optical and electrical properties of the films is discussed.ZnOfilms annealed with higher temperature showed an extremely sharp (002) peak in the XRD patterns, indicates increased crystallization. The optical transmittance spectra of the films is found to change with annealing temperature and showed a very good transmittance (between 80 to 90%) with the films prepared at 600°C showed highest optical transparency within the visible wavelength region. The absorption edge analysis revealed that the optical band gap is found to increase with annealing temperature up to 3.5 eV at 600°C and decreased with higher temperature. Electronic transition was found to be direct transition type. The minimum electrical resistivity of 55 Ω-cm was obtained for the films annealed at 600°C.
Suggested Citation
M. Rusop & K. Uma & T. Soga & T. Jimbo, 2005.
"Optical And Electrical Properties Of Zinc Oxide Thin Films Dip-Coated Of Sol–Gel Method,"
Surface Review and Letters (SRL), World Scientific Publishing Co. Pte. Ltd., vol. 12(05n06), pages 697-701.
Handle:
RePEc:wsi:srlxxx:v:12:y:2005:i:05n06:n:s0218625x05007700
DOI: 10.1142/S0218625X05007700
Download full text from publisher
As the access to this document is restricted, you may want to search for a different version of it.
Corrections
All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:wsi:srlxxx:v:12:y:2005:i:05n06:n:s0218625x05007700. See general information about how to correct material in RePEc.
If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.
We have no bibliographic references for this item. You can help adding them by using this form .
If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.
For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Tai Tone Lim (email available below). General contact details of provider: http://www.worldscinet.com/srl/srl.shtml .
Please note that corrections may take a couple of weeks to filter through
the various RePEc services.