IDEAS home Printed from https://ideas.repec.org/a/wsi/ijmpcx/v32y2021i02ns0129183121500297.html
   My bibliography  Save this article

Studying the arrangement of submerged vanes group in a straight alluvial channel using numerical modeling of flow and bed topography around a single vane

Author

Listed:
  • M. Rostamabadi

    (Department of Civil Engineering, Buinzahra Branch, Islamic Azad University, Buinzahra, Iran)

  • H. Montaseri

    (#x2020;Department of Civil Engineering, Yasouj University, Yasouj, Iran)

  • Seyed Ali Akbar Salehi Neyshabouri

    (#x2021;Department of Civil and Environmental Engineering, Tarbiat Modares University, Tehran, Iran)

  • A. R. Zarrati

    (#xA7;Department of Civil and Environmental Engineering, Amirkabir University, Tehran, Iran)

Abstract

Submerged vanes are installed in waterways bed. These structures are usually used in groups and their main performance is to create an eddy current which leads to change in stream flow pattern and the bed topography in waterways. Performance of submerged vanes group depends on their arrangement and size. In this study using SSIIM numerical model, hydrodynamic analysis of flow pattern and bed topography around a single submerged vane in a straight channel was done and tried to estimate proper arrangement of submerged vanes group. The geometry of arrangement consisted of longitudinal distance between consecutive vanes, transverse distance of two adjacent vanes, and transverse distance of submerged vanes from the outer wall. Therefore, after verification of the results of numerical model with experimental data, flow pattern and topography of the bed around a vane with different dimensions and angles (in suggested domain) were investigated and analyzed. In this order, values of transverse and longitudinal distances of scouring hole at high-pressure and low-pressure sides of the vane from center of the vane were measured. Also values of transverse and longitudinal locations of the maximum scouring hole and maximum sedimentation downstream of the vane were determined. The results of these parameters were used to estimate the location of adjacent vanes. To reduce number of modes, the Taguchi method is used in design of simulations. Finally, mathematical relations are derived for geometry of arrangement versus vanes dimensions and angles. Comparison of the results of this research with the results of previous researchers, who have studied submerged vanes groups, showed that accuracy of the method used in this study is acceptable. The numerical results showed that the values obtained for the transverse and longitudinal distances of vanes are almost in the same range of previous laboratory studies.

Suggested Citation

  • M. Rostamabadi & H. Montaseri & Seyed Ali Akbar Salehi Neyshabouri & A. R. Zarrati, 2021. "Studying the arrangement of submerged vanes group in a straight alluvial channel using numerical modeling of flow and bed topography around a single vane," International Journal of Modern Physics C (IJMPC), World Scientific Publishing Co. Pte. Ltd., vol. 32(02), pages 1-18, February.
  • Handle: RePEc:wsi:ijmpcx:v:32:y:2021:i:02:n:s0129183121500297
    DOI: 10.1142/S0129183121500297
    as

    Download full text from publisher

    File URL: http://www.worldscientific.com/doi/abs/10.1142/S0129183121500297
    Download Restriction: Access to full text is restricted to subscribers

    File URL: https://libkey.io/10.1142/S0129183121500297?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:wsi:ijmpcx:v:32:y:2021:i:02:n:s0129183121500297. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Tai Tone Lim (email available below). General contact details of provider: http://www.worldscinet.com/ijmpc/ijmpc.shtml .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.