IDEAS home Printed from https://ideas.repec.org/a/taf/gcmbxx/v24y2021i1p21-32.html
   My bibliography  Save this article

Effect of foam densification and impact velocity on the performance of a football helmet using computational modeling

Author

Listed:
  • Samuel T. Mills
  • Trevor S. Young
  • Lillian S. Chatham
  • Sourav Poddar
  • R. Dana Carpenter
  • Christopher M. Yakacki

Abstract

The NFL recently released validated helmet-impact models to study the performance of currently used helmets. This study used the model of a Riddell Speed Classic helmet to determine the influence of the properties of protective foam padding on acceleration and deformation at two common impact locations to cause concussions. The performance of the helmet was measured before and after manipulating the material properties of the protective foam liner material using FEA software. The densification strain was adjusted by using the scale factor tool in LS-DYNA to create four material categories – soft, standard, stiff, and rigid. The helmet was tested under side and rear impacts using the four material properties at 2.0, 5.5, 7.4, 9.3 and 12.3 m/s impact speeds using the NOCSAE linear impactor model. This study suggests that the standard foam material compresses to a range that could be considered to have “bottomed out” at impact speeds at 5.5 m/s for side impacts. Despite testing a wide range of material properties, the measured accelerations did not vary dramatically across material properties. Rather, impact speed played the dominant role on measured acceleration. This is the first study to demonstrate how open-source impact models can be used to run a design of experiments and investigate the role between different materials used inside a helmet and football helmet performance.

Suggested Citation

  • Samuel T. Mills & Trevor S. Young & Lillian S. Chatham & Sourav Poddar & R. Dana Carpenter & Christopher M. Yakacki, 2021. "Effect of foam densification and impact velocity on the performance of a football helmet using computational modeling," Computer Methods in Biomechanics and Biomedical Engineering, Taylor & Francis Journals, vol. 24(1), pages 21-32, May.
    • Handle: RePEc:taf:gcmbxx:v:24:y:2021:i:1:p:21-32
    DOI: 10.1080/10255842.2020.1807015
    as

    Download full text from publisher

    File URL: http://hdl.handle.net/10.1080/10255842.2020.1807015
    Download Restriction: Access to full text is restricted to subscribers.
    File URL: https://libkey.io/10.1080/10255842.2020.1807015?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    More about this item

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:taf:gcmbxx:v:24:y:2021:i:1:p:21-32. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Chris Longhurst (email available below). General contact details of provider: http://www.tandfonline.com/gcmb .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.