IDEAS home Printed from https://ideas.repec.org/a/spr/joinma/v32y2021i1d10.1007_s10845-020-01569-y.html
   My bibliography  Save this article

Modal parameter identification of general cutter based on milling stability theory

Author

Listed:
  • Minglong Guo

    (Dalian University of Technology)

  • Zhaocheng Wei

    (Dalian University of Technology)

  • Minjie Wang

    (Dalian University of Technology)

  • Shiquan Li

    (Dalian University of Technology)

  • Jia Wang

    (Dalian University of Technology)

  • Shengxian Liu

    (Dalian University of Technology)

Abstract

In the field of CNC milling, chatter has been a hot research topic, which is related to machining quality, precision and cost. Stability lobe diagram (SLD) reflects the vibration of the machining system under different process parameters and cutter axis vectors that is significant for optimization. The accurate dynamic characteristics of the machining system is the prerequisite for stability analysis. Finite element simulation is mainly aimed at small diameter cutter system, and accuracy is poor. The most widely used method is hammer test, but the equipment is expensive, the operation is too professional and it cannot reflect the dynamic characteristics of the machining system in working status. This paper proposes an undetermined coefficient method for the general cutter system to identify the modal parameters, that are the natural frequency, stiffness and damping ratio, just based on the very simple experiment of three-axis half-immersion milling in horizontal plane. Firstly, considering the exact in-cut cutting edge and the instantaneous cutting force coefficient corresponding to the axial factor and the chip thickness, the dynamic model of three-axis milling machining for the general cutter is established. Secondly, two implicit conditions of stable critical speed and cutting depth are derived based on feedback control theory in the frequency domain. Thirdly, the two sets of critical cutting depth and the chatter frequency under arbitrary speeds are obtained by using the dichotomy. With the method proposed in this paper, one of the two is used to solve a series of modal parameter sets, and the other of the two is used to extract the optimal modal parameters in the modal parameter sets. Finally, taking the identified modal parameters as known conditions to search the points one by one in the two-dimensional space composed of the rotational speed and the cutting depth, and judge whether it meets the critical conditions. SLD can be obtained by connecting the points that satisfy critical conditions together. Based on the previous experiment of flat-end cutter, it verified the feasibility of the modal parameter identification method in the paper. In the designed three-axis milling experiment of the ball-end cutter, the in-cut cutting edge simulation and the cutting force coefficient identification were carried out, and the modal parameters of the cutter system were also obtained successfully. The plotted lobe diagram was verified by the spectrum analysis result of the vibration signal collected by the acceleration sensor.

Suggested Citation

  • Minglong Guo & Zhaocheng Wei & Minjie Wang & Shiquan Li & Jia Wang & Shengxian Liu, 2021. "Modal parameter identification of general cutter based on milling stability theory," Journal of Intelligent Manufacturing, Springer, vol. 32(1), pages 221-235, January.
    • Handle: RePEc:spr:joinma:v:32:y:2021:i:1:d:10.1007_s10845-020-01569-y
    DOI: 10.1007/s10845-020-01569-y
    as

    Download full text from publisher

    File URL: http://link.springer.com/10.1007/s10845-020-01569-y
    File Function: Abstract
    Download Restriction: Access to the full text of the articles in this series is restricted.
    File URL: https://libkey.io/10.1007/s10845-020-01569-y?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. M. Pour & M. A. Torabizadeh, 2016. "Improved prediction of stability lobes in milling process using time series analysis," Journal of Intelligent Manufacturing, Springer, vol. 27(3), pages 665-677, June.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Congying Deng & Jielin Tang & Jianguo Miao & Yang Zhao & Xiang Chen & Sheng Lu, 2023. "Efficient stability prediction of milling process with arbitrary tool-holder combinations based on transfer learning," Journal of Intelligent Manufacturing, Springer, vol. 34(5), pages 2263-2279, June.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Congying Deng & Jielin Tang & Jianguo Miao & Yang Zhao & Xiang Chen & Sheng Lu, 2023. "Efficient stability prediction of milling process with arbitrary tool-holder combinations based on transfer learning," Journal of Intelligent Manufacturing, Springer, vol. 34(5), pages 2263-2279, June.
    2. Jianfeng Tao & Chengjin Qin & Dengyu Xiao & Haotian Shi & Xiao Ling & Bingchu Li & Chengliang Liu, 2020. "Timely chatter identification for robotic drilling using a local maximum synchrosqueezing-based method," Journal of Intelligent Manufacturing, Springer, vol. 31(5), pages 1243-1255, June.
    3. Feng Feng & Meng Yuan & Yousheng Xia & Haoming Xu & Pingfa Feng & Xinghui Li, 2022. "Roughness Scaling Extraction Accelerated by Dichotomy-Binary Strategy and Its Application to Milling Vibration Signal," Mathematics, MDPI, vol. 10(7), pages 1-17, March.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:spr:joinma:v:32:y:2021:i:1:d:10.1007_s10845-020-01569-y. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Sonal Shukla or Springer Nature Abstracting and Indexing (email available below). General contact details of provider: http://www.springer.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.