IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v16y2024i11p4692-d1406235.html
   My bibliography  Save this article

Utilizing the Taguchi Method to Optimize Rotor Blade Geometry for Improved Power Output in Ducted Micro Horizontal-Axis Wind Turbines

Author

Listed:
  • Kwan Ouyang

    (Department of Aerospace Engineering, Tamkang University, No.151, Yingzhuan Rd., Tamsui Dist., New Taipei City 251301, Taiwan)

  • Tzeng-Yuan Chen

    (Department of Aerospace Engineering, Tamkang University, No.151, Yingzhuan Rd., Tamsui Dist., New Taipei City 251301, Taiwan)

  • Jun-Jie You

    (Department of Aerospace Engineering, Tamkang University, No.151, Yingzhuan Rd., Tamsui Dist., New Taipei City 251301, Taiwan)

Abstract

This numerical study utilized the Taguchi method to systematically optimize the blade geometry of a ducted micro horizontal-axis wind turbine (HAWT) for moving vehicles to enhance the output power coefficient. Three geometric parameters of the rotor, namely, the number of blades, rotor solidity, and blade pitch angle, were investigated. The optimum parameter design includes eight blades, rotor solidity of 60%, and a pitch angle of 30°, where the blade pitch angle had the most significant effect on the rotor performance. This result confirms that high rotor solidity is more suitable for micro HAWT. The C P,max value achieved with the optimum geometry was 0.432, which was 39.4% higher than that achieved with the worst blade geometry. The aerodynamic characteristics of this wind turbine were also investigated. Compared with the worst blade geometry, the rotor with the optimum blade geometry drew more airflow into the duct and exhibited a higher C P,max due to a greater pressure difference between the windward and leeward sides of the blades. The optimum blade geometry achieved a C T,max of 0.43, which was 38.7% higher than the worst blade geometry. The investigated untwisted blades exhibited low torque near their tips; therefore, the use of twisted blades is recommended for further increasing the torque generated at the blade tip and thus the turbine’s output power. This study facilitates insight into blade geometry effects on rotor performance and helps improve wind energy efficiency, contributing to sustainable development goals (SDGs) like SDG 7 (affordable and clean energy).

Suggested Citation

  • Kwan Ouyang & Tzeng-Yuan Chen & Jun-Jie You, 2024. "Utilizing the Taguchi Method to Optimize Rotor Blade Geometry for Improved Power Output in Ducted Micro Horizontal-Axis Wind Turbines," Sustainability, MDPI, vol. 16(11), pages 1-22, May.
  • Handle: RePEc:gam:jsusta:v:16:y:2024:i:11:p:4692-:d:1406235
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/16/11/4692/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2071-1050/16/11/4692/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Eslam S. Abdelghany & Hesham H. Sarhan & Raed Alahmadi & Mohamed B. Farghaly, 2023. "Study the Effect of Winglet Height Length on the Aerodynamic Performance of Horizontal Axis Wind Turbines Using Computational Investigation," Energies, MDPI, vol. 16(13), pages 1-20, July.
    2. Rahmatian, Mohammad Ali & Nazarian Shahrbabaki, Amin & Moeini, Seyed Peyman, 2023. "Single-objective optimization design of convergent-divergent ducts of ducted wind turbine using RSM and GA, to increase power coefficient of a small-scale horizontal axis wind turbine," Energy, Elsevier, vol. 269(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Po-Wen Hwang & Jia-Heng Wu & Yuan-Jen Chang, 2024. "Optimization Based on Computational Fluid Dynamics and Machine Learning for the Performance of Diffuser-Augmented Wind Turbines with Inlet Shrouds," Sustainability, MDPI, vol. 16(9), pages 1-31, April.
    2. Rahmatian, Mohammad Ali & Hashemi Tari, Pooyan & Majidi, Sahand & Mojaddam, Mohammad, 2023. "Experimental study of the effect of the duct on dual co-axial horizontal axis wind turbines and the effect of rotors diameter ratio and distance on increasing power coefficient," Energy, Elsevier, vol. 284(C).
    3. Ngwarai Shambira & Golden Makaka & Patrick Mukumba, 2024. "Velocity Augmentation Model for an Empty Concentrator-Diffuser-Augmented Wind Turbine and Optimisation of Geometrical Parameters Using Surface Response Methodology," Sustainability, MDPI, vol. 16(4), pages 1-30, February.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:16:y:2024:i:11:p:4692-:d:1406235. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.