IDEAS home Printed from https://ideas.repec.org/a/gam/jijerp/v17y2020i13p4634-d377129.html
   My bibliography  Save this article

Leveraging 3D Printing Capacity in Times of Crisis: Recommendations for COVID-19 Distributed Manufacturing for Medical Equipment Rapid Response

Author

Listed:
  • Albert Manero

    (Limbitless Solutions, University of Central Florida, 4217 E Plaza Drive, Orlando, FL 32816, USA)

  • Peter Smith

    (Limbitless Solutions, University of Central Florida, 4217 E Plaza Drive, Orlando, FL 32816, USA)

  • Amanda Koontz

    (Department of Sociology, University of Central Florida, 4000 Central Florida Blvd, Orlando, FL 32816, USA)

  • Matt Dombrowski

    (Limbitless Solutions, University of Central Florida, 4217 E Plaza Drive, Orlando, FL 32816, USA)

  • John Sparkman

    (Limbitless Solutions, University of Central Florida, 4217 E Plaza Drive, Orlando, FL 32816, USA)

  • Dominique Courbin

    (Limbitless Solutions, University of Central Florida, 4217 E Plaza Drive, Orlando, FL 32816, USA)

  • Albert Chi

    (Division of Trauma, Critical Care & Acute Care Surgery, Department of Surgery, Oregon Health and Science University, 3181 SW Sam Jackson Park Rd, Portland, OR 97239, USA)

Abstract

The SARS-CoV-2 (COVID-19) pandemic has provided a unique set of global supply chain limitations with an exponentially growing surge of patients requiring care. The needs for Personal Protective Equipment (PPE) for hospital staff and doctors have been overwhelming, even just to rule out patients not infected. High demand for traditionally manufactured devices, challenged by global demand and limited production, has resulted in a call for additive manufactured (3D printed) equipment to fill the gap between traditional manufacturing cycles. This method has the unique ability to pivot in real time, while traditional manufacturing may take months to change production runs. 3D printing has been used to produce a variety of equipment for hospitals including face shields, masks, and even ventilator components to handle the surge. This type of rapid, crowd sourced, design and production resulted in new challenges for regulation, liability, and distribution. This manuscript reviews these challenges and successes of additive manufacturing and provides a forward plan for hospitals to consider for future surge events. Recommendations: To accommodate future surges, hospitals and municipalities should develop capacity for short-run custom production, enabling them to validate new designs. This will rapidly increase access to vetted equipment and critical network sharing with community distributed manufacturers and partners. Clear guidance and reviewed design repositories by regulatory authorities will streamline efforts to combat future pandemic waives or other surge events.

Suggested Citation

  • Albert Manero & Peter Smith & Amanda Koontz & Matt Dombrowski & John Sparkman & Dominique Courbin & Albert Chi, 2020. "Leveraging 3D Printing Capacity in Times of Crisis: Recommendations for COVID-19 Distributed Manufacturing for Medical Equipment Rapid Response," IJERPH, MDPI, vol. 17(13), pages 1-17, June.
    • Handle: RePEc:gam:jijerp:v:17:y:2020:i:13:p:4634-:d:377129
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1660-4601/17/13/4634/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1660-4601/17/13/4634/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Albert Manero & Peter Smith & John Sparkman & Matt Dombrowski & Dominique Courbin & Anna Kester & Isaac Womack & Albert Chi, 2019. "Implementation of 3D Printing Technology in the Field of Prosthetics: Past, Present, and Future," IJERPH, MDPI, vol. 16(9), pages 1-15, May.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Nishant Saravanan & Jessica Olivares-Aguila & Alejandro Vital-Soto, 2022. "Bibliometric and Text Analytics Approaches to Review COVID-19 Impacts on Supply Chains," Sustainability, MDPI, vol. 14(23), pages 1-33, November.
    2. Nicola Luigi Bragazzi, 2020. "Digital Technologies-Enabled Smart Manufacturing and Industry 4.0 in the Post-COVID-19 Era: Lessons Learnt from a Pandemic," IJERPH, MDPI, vol. 17(13), pages 1-2, July.
    3. Nylund, Petra A. & Amores-Bravo, Xavier & Ferràs-Hernández, Xavier & Brem, Alexander, 2023. "Crisis as a catalyst of idle innovation ecosystems: Evidence from ecosystem exaptation of a water partnership," Technological Forecasting and Social Change, Elsevier, vol. 197(C).
    4. Po-Sheng Ko & Jen-Yao Lee, 2021. "Analysis of Taiwan’s Mask Collection and Plan Evasion during the COVID-19 Pandemic," IJERPH, MDPI, vol. 18(8), pages 1-20, April.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Joost van Hoof & Deirdre M. Beneken genaamd Kolmer & Erwin de Vlugt & Sanne I. de Vries, 2019. "Quality of Life: The Interplay between Human Behaviour, Technology and the Environment," IJERPH, MDPI, vol. 16(24), pages 1-7, December.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jijerp:v:17:y:2020:i:13:p:4634-:d:377129. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.