IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v17y2024i4p970-d1341501.html
   My bibliography  Save this article

Impact of H 2 Blending of Methane on Micro-Diffusion Combustion in a Planar Micro-Combustor with Splitter

Author

Listed:
  • Sreejith Sudarsanan

    (Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India)

  • Ratna Kishore Velamati

    (Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India)

  • Awad B. S. Alquaity

    (Department of Mechanical Engineering, King Fahd University of Petroleum & Minerals, Dhahran 31261, Saudi Arabia
    Center for Hydrogen and Energy Storage, King Fahd University of Petroleum & Minerals, Dhahran 31261, Saudi Arabia)

  • Prabhu Selvaraj

    (Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India)

Abstract

An investigation into the non-premixed combustion characteristics of methane in a planar micro-combustor with a splitter was performed. The impact of blending methane with hydrogen on these characteristics was also analyzed. Additionally, the effects of inlet velocity and global equivalence ratio on flame location, flame temperature, combustion efficiency and outer wall temperature were studied for three different fuel compositions: pure methane (MH0), 60% methane with 40% hydrogen (MH40), and 40% methane with 60% hydrogen (MH60)). A heat recirculation analysis of the combustor wall was conducted to determine the amount of heat recirculated into the unburnt gas at various inlet velocities for all three fuel compositions. The results demonstrated that the stability limit of methane in terms of inlet velocity (1–2 m/s) and global equivalence ratio (1.0–1.2) was significantly enhanced to 1–3 m/s and 0.8–1.2, respectively, with the addition of hydrogen. At an inlet velocity of 2 m/s, the flame location of 3.6 mm for MH0 was significantly improved to 2.2 mm for MH60. Additionally, outer wall temperature exhibited a rise of 100 K for MH60 compared to MH0. Furthermore, from heat recirculation analysis, when the ratio of heat recirculated to heat loss exceeded unity, the flame started exhibiting the lift-off phenomenon for all the fuel compositions.

Suggested Citation

  • Sreejith Sudarsanan & Ratna Kishore Velamati & Awad B. S. Alquaity & Prabhu Selvaraj, 2024. "Impact of H 2 Blending of Methane on Micro-Diffusion Combustion in a Planar Micro-Combustor with Splitter," Energies, MDPI, vol. 17(4), pages 1-22, February.
    • Handle: RePEc:gam:jeners:v:17:y:2024:i:4:p:970-:d:1341501
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/17/4/970/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/17/4/970/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Vinay Sankar & Sreejith Sudarsanan & Sudipto Mukhopadhyay & Prabhu Selvaraj & Aravind Balakrishnan & Ratna Kishore Velamati, 2023. "Towards the Development of Miniature Scale Liquid Fuel Combustors for Power Generation Application—A Review," Energies, MDPI, vol. 16(10), pages 1-41, May.
    2. Cai, Tao & Tang, Aikun & Zhao, Dan & Zhou, Chen & Huang, Qiuhan, 2020. "Flame dynamics and stability of premixed methane/air in micro-planar quartz combustors," Energy, Elsevier, vol. 193(C).
    3. Aravind Muraleedharan & Jithin Edacheri Veetil & Akram Mohammad & Sudarshan Kumar & Ratna Kishore Velamati, 2021. "Effect of Burner Wall Material on Microjet Hydrogen Diffusion Flames near Extinction: A Numerical Study," Energies, MDPI, vol. 14(24), pages 1-24, December.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Ruslan V. Fedorov & Dmitry A. Generalov & Vyacheslav V. Sherkunov & Valeriy V. Sapunov & Sergey V. Busygin, 2023. "Improving the Efficiency of Fuel Combustion with the Use of Various Designs of Embrasures," Energies, MDPI, vol. 16(11), pages 1-15, May.
    2. Zhao, He & Zhao, Dan & Becker, Sid & Rong, Hui & Zhao, Xiaohuan, 2023. "Entropy generation and improved thermal performance investigation on a hydrogen-fuelled double-channel microcombustor with Y-shaped internal fins," Energy, Elsevier, vol. 283(C).
    3. Tang, Aikun & Cai, Tao & Li, Chong & Zhou, Chen & Gao, Lingjie, 2024. "Flame visualization and spectral analysis of combustion instability in a premixed methane/air-fueled micro-combustor," Energy, Elsevier, vol. 294(C).
    4. Wang, Yong & Ma, Yinjie & Xie, Deyi & Yu, Zhenhuan & E, Jiaqiang, 2021. "Numerical study on the influence of gasoline properties and thermodynamic conditions on premixed laminar flame velocity at multiple conditions," Energy, Elsevier, vol. 233(C).
    5. Yang, Xiao & Yang, Wenming & Dong, Shikui & Tan, Heping, 2020. "Flame stability analysis of premixed hydrogen/air mixtures in a swirl micro-combustor," Energy, Elsevier, vol. 209(C).
    6. Sun, Bowen & Kang, Xin & Wang, Yu, 2020. "Numerical investigations on the methane-oxygen diffusion flame-street phenomena in a microchannel: Effects of wall temperatures, inflow rates and global equivalence ratios on flame behaviors and combu," Energy, Elsevier, vol. 207(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:17:y:2024:i:4:p:970-:d:1341501. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.