IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v16y2023i21p7230-d1266288.html
   My bibliography  Save this article

New Insights into Flow for a Low-Bypass-Ratio Transonic Fan with Optimized Rotor

Author

Listed:
  • Mingjun Liu

    (Shenzhen Institute of Information Technology, Shenzhen 518172, China)

  • Zhenjiu Zhang

    (Shenzhen Institute of Information Technology, Shenzhen 518172, China)

  • Zhuoming Liang

    (Harbin Institute of Technology, Harbin 150001, China)

  • Haibing Xiao

    (Shenzhen Institute of Information Technology, Shenzhen 518172, China)

  • Huanlong Chen

    (Harbin Institute of Technology, Harbin 150001, China)

  • Xianqing Yang

    (Yobow Turbofan (Shenzhen) Co., Ltd., Shenzhen 518055, China)

  • Changxiao Shao

    (Harbin Institute of Technology (Shenzhen), Shenzhen 518055, China)

Abstract

In this paper, a three-dimensional aerodynamics optimization system is built and applied to optimize a rotor blade to balance the conflicts between stall margin, total pressure ratio, adiabatic efficiency, and mass flow rate for the high-loading and transonic-flow fan. A novel flow diagnostic method based on vorticity dynamics theory is utilized to analyze the reasons for the improvement in aerodynamic performance in the optimized transonic fan. In the established aerodynamic optimization method, use the blade profile camber line curvature and its leading edge metal angle as the optimization variables, which are optimized by modifying the coordinates of their control points and introducing a genetic algorithm. Finally, the vorticity dynamics parameters, such as the boundary vorticity flux (BVF), azimuthal vorticity and skin-friction lines are used to diagnose the key flow features in the optimized and baseline fan passage. The results indicate that, by controlling skillfully the blade camber line curvature in the optimization improves the aerodynamic performance of the fan stage, increasing the total pressure ratio by 1.90% while increasing the mass flow rate and adiabatic efficiency by 5.82% and 4.45%, respectively. The formulas from the vorticity dynamics diagnosis method indicate a close link between the aerodynamic performance and vorticity dynamic parameters for the axial fan/compressor passage flow, and that both azimuthal vorticity and boundary vorticity flux have significant influence on fan stage performance. Moreover, the boundary layer separation flow on the rotor blade surface is accompanied by a spike of entropy and static pressure, and their derivative/gradient also suffer drastic changes under the effect of shock waves. Detailed flow information can be obtained about the on-wall with high accuracy based on the vorticity dynamics diagnosis method, which provides researchers with a novel method for the turbomachinery aerodynamic design and analysis in the aero-engine engineering development field.

Suggested Citation

  • Mingjun Liu & Zhenjiu Zhang & Zhuoming Liang & Haibing Xiao & Huanlong Chen & Xianqing Yang & Changxiao Shao, 2023. "New Insights into Flow for a Low-Bypass-Ratio Transonic Fan with Optimized Rotor," Energies, MDPI, vol. 16(21), pages 1-19, October.
    • Handle: RePEc:gam:jeners:v:16:y:2023:i:21:p:7230-:d:1266288
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/16/21/7230/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/16/21/7230/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Carlo Cravero & Davide De Domenico & Davide Marsano, 2023. "Uncertainty Quantification Analysis of Exhaust Gas Plume in a Crosswind," Energies, MDPI, vol. 16(8), pages 1-22, April.
    2. Piotr Wiśniewski & Guojie Zhang & Sławomir Dykas, 2022. "Numerical Investigation of the Influence of Air Contaminants on the Interfacial Heat Transfer in Transonic Flow in a Compressor Rotor," Energies, MDPI, vol. 15(12), pages 1-21, June.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Michał Frant & Stanisław Kachel & Wojciech Maślanka, 2023. "Gust Modeling with State-of-the-Art Computational Fluid Dynamics (CFD) Software and Its Influence on the Aerodynamic Characteristics of an Unmanned Aerial Vehicle," Energies, MDPI, vol. 16(19), pages 1-19, September.
    2. Maria Hurnik & Piotr Ciuman & Zbigniew Popiolek, 2024. "Eddy–Viscosity Reynolds-Averaged Navier–Stokes Modeling of Air Distribution in a Sidewall Jet Supplied into a Room," Energies, MDPI, vol. 17(5), pages 1-19, March.
    3. Yinghua Chai & Yuansheng Lin & Qi Xiao & Chonghai Huang & Hanbing Ke & Bangming Li, 2024. "Numerical Simulation on Two-Phase Ejector with Non-Condensable Gas," Energies, MDPI, vol. 17(6), pages 1-19, March.
    4. Alberto Savino & Andrea Ferreri & Alex Zanotti, 2024. "Validation of a Mid-Fidelity Numerical Approach for Wind Turbine Aerodynamics Characterization," Energies, MDPI, vol. 17(7), pages 1-23, March.
    5. Hyunjun Jang & Junho Suh, 2024. "Flow Characteristic Analysis of the Impeller Inlet Diameter in a Double-Suction Pump," Energies, MDPI, vol. 17(9), pages 1-18, April.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:16:y:2023:i:21:p:7230-:d:1266288. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.